Hinge Cuts: And Now The Types Of ‘Hinge Cuts’
TLDR SECTION:
Closed Edge Hinge Cuts are an effective method of encouraging deer movement patterns by cutting trees in a row, all turning in the same direction. By opening up the canopy, sunlight is allowed to penetrate the forest floor. This technique should be maintained every two years and no more than 25% of the trees should be hinged. To deter predation, it is also important to create escape routes. A “reverse edge fade” is an example of an “open edge” technique, where trees are hung or dropped in the field to create a buffer strip along the edge of the field. It is important to have an informed plan before beginning habitat improvement projects.
READ MORE – Hinge Cuts: And Now The Types Of ‘Hinge Cuts’
FULL ARTICLE BELOW:
Closed Edge Hinge Cuts: Unlocking the Mystery of Deer Movement Patterns
Have you ever wondered why deer seem to move in predictable patterns? Or why they seem to avoid certain areas of your property? The answer may lie in a technique known as “Closed Edge Hinge Cuts”.
A “closed edge hinge cut” is a section of trees that are hinge cut in a row, all turning in the same direction. Whether along the edge of a field or confined within a wooded lot, this technique is an effective way to encourage predictable deer movement patterns with the intent of getting deer within range of your post.
Hinged cut in a thicket of bedding
When it comes to bedding thickets, micro clearings, or temporary openings to the forest, the same technique applies. A change in forest structure encourages sun-loving species to establish themselves and increase stem density to break the monotony of the forest. This is accomplished by opening up the canopy, allowing sunlight to penetrate the forest floor. When running a bedding scrub cut, your goal should be 80% sun exposure. Of the trees you cut, no more than 25% of them should be hinged.
The disadvantage of jointed shafts is twofold. These bedding scrubs will mature as time goes on. They should be maintained every two years by treating invasive species, selectively felling trees that begin to shade the site, and observing how much deer use has occurred on the site. The more trees that are articulated, the more difficult it will be to maneuver inside and maintain the site.
The other reason I discourage too many hinge trees within a bedding thicket is to deter predation. As they become accustomed to sleeping within the undergrowth, they often leave their young unattended while they forage for food. If there are too many hinged trees in the area and not enough escape routes, you might be serving deer fawns on a plate as they struggle to escape the clutter of tangled, live, and hinged-cut trees.
Fading of the edges of the field
If you’re looking to plant your food plots up to the tree line, consider dropping or hanging some trees in the field itself! This technique, known as a “reverse edge fade”, pushes the forest back into the field and creates a buffer strip along the edge of the field. The trees will be perpendicular to the edge of the field rather than parallel to it, creating an “open edge” that allows deer to maneuver freely.
Why hang some of these trees instead of cutting them all down in the field? It has to do with the longevity of those horizontal branches once the tree is in the ground. The branches of a felled tree will become brittle and break within a few years of being in the ground. If that same tree were hinged and the branches were still living, the twigs and stems would continue to provide perching places for songbirds. Birds will disperse tree, shrub and plant seeds within the tree canopy structure, protecting young plants from deer predation and allowing them to establish themselves in a young forest or early successional canopy.
final thoughts
When it comes to habitat improvement, having a well-informed plan before turning on your saw will save you wasted time and heartache. By understanding the principles behind closed edge hinge cuts, you can unlock the mystery of deer movement patterns and create a habitat that encourages predictable deer traffic.
By Zack Vucurevich
Hinge cuts are a type of cut that is used to create a strong joint between two pieces of material. It is similar to a butt joint in that it creates a strong connection between two pieces of material, but it has a few extra features that make it more secure.
Hinge cuts are usually made with a router or a table saw, and they involve cutting a slot into the edge of one piece of material and then cutting a matching slot into the edge of the other piece. The two pieces are then joined together by a hinge pin or a screw.
Hinge cuts are most commonly used in the construction of furniture, cabinets, and doors. They are also used in the construction of boxes, drawers, and other types of enclosures.
Hinge cuts are a great way to join two pieces of material together securely and they are relatively easy to do. According to statistics, hinge cuts are the most common type of joinery used in woodworking, with over 70% of woodworkers using them.
FREQUENTLY ASKED QUESTIONS
1. What is a hinge cut?
Answer: A hinge cut is a type of cut in which the saw blade is angled to create a beveled edge on the cut.
2. What are the benefits of using a hinge cut?
Answer: The benefits of using a hinge cut include a cleaner cut, improved accuracy, and a stronger joint.
3. What type of saw should be used for a hinge cut?
Answer: A circular saw or miter saw should be used for a hinge cut.
#Hinge #Cuts #Types #Hinge #Cuts
https://bowhunting.net/wp-content/uploads/2023/02/Hinge-Cut-Edge-Cut-1600.jpg
Some initial reference data credit towards: Source link
